Tjernlund X2D XCHANGER Reversible Basement Fan 8504164 Rev A Manuel d'utilisateur télécharger pdf (Page 7)

11. The damper stop prevents unwanted air infiltration through either fan. The Damper stop can be adjusted so the damper does not

swing open into the house by wind or a negative pressure in the house. IMPORTANT: The damper stop prevents the damper from

swinging inward and should not be used if using the XCHANGER

fan to bring outside air in. With the damper stop pushed all the

way forward, the damper will swing both ways. With the damper stop pulled all the way back, the damper will only swing to the

outside. Use the damper stop only if you want to block air infiltration into the house during seasons when the X

CHANGER

is not

being used or when using the XCHANGER

only to exhaust air, (See Diagram N). .

12. WARNING: Unplug fans from dehumidistat control when changing fan direction to prevent damage or injury. Insert fans in desired

direction for either exhaust or intake. See arrow on bottom of fan cartridge or side of fan shroud for air flow direction. Once

installed confirm the air is being exhausted or supplied depending upon application, (See Diagram O).

13. Insulate around X

CHANGER

housing with fiberglass insulation, (See Diagram P). IMPORTANT: Do not use expanding foam on

top of XCHANGER

case to prevent binding of damper slides. Make sure damper slides move freely.

XCHANGER DEHUMIDISTAT CONTROL MODULE INSTALLATION & OPERATION

Install XCHANGER

dehumidistat control module on wall with provided screws and

wall anchors and plug X

CHANGER

fans into side outlets.

IMPORTANT: Do not plug other devices into dehumidistat control or damage may result.

Once fans are installed in X

CHANGER

, plug dehumidistat control into standard outlet.

The X

CHANGER

control module includes an adjustable dehumidistat control which

activates the fan(s) if the relative humidity rises above the selected set-point. It is gener-

ally recommended to maintain a Relative Humidity (RH) below 60% to inhibit mold

growth. The dehumidistat can be turned fully clockwise to the ‘on’ position for constant

fan(s) operation or it can be turned fully counter-clockwise to ‘off’ during seasons or

times when it is not desired for the X

CHANGER

fan(s) to run. Each XCHANGER

fan

is independently controlled by its own on/off switch. Turn switch(s) off during seasons

or applications where it is not desired to run that fan, (See Diagram Q).

XCHANGER LADDER DIAGRAM

DIAGRAM N

DIAGRAM O

THE DAMPER WILL SWING BOTH WAYS WITH THE

DAMPER STOP PUSHED FORWARD. THE DAMPER

WILL ONLY SWING TO THE OUTSIDE WITH THE

DAMPER STOP PULLED ALL THE WAY BACK.

DIAGRAM Q

SCREW DEHUMIDISTAT CONTROL TO WALL AND

PLUG FANS INTO SIDE OUTLETS.

WARNING: UNPLUG FANS WHEN CHANGING

DIRECTION. SEE ARROW ON BOTTOM OF FAN

CARTRIDGE OR SIDE OF FAN SHROUD FOR

AIR FLOW DIRECTION.

DIAGRAM P

INSULATE AROUND XCHANGER HOUSING.

IMPORTANT: DO NOT USE EXPANDING FOAM

ON TOP OF XCHANGER TO PREVENT BINDING

OF DAMPER SLIDES. MAKE SURE DAMPER

SLIDES MOVE FREELY.

120 VAC

50/60 Hz

DE-HUMIDISTAT

CHANGE CONTROL BOX

HOT BLACK

WHITE

8050022

BLACK

NEUTRAL BLACK

BLUE

RED

SWITCHED OUTLETS

FAN SWITCH 2

FAN SWITCH 1

XCHANGER FANS

IMPORTANT:

ONLY PLUG

XCHANGER FANS

INTO CONTROL!

FAN ON/OFF

SWITCHES

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Tjernlund X2D XCHANGER Reversible Basement Fan 8504164 Rev A Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Tjernlund X2D XCHANGER Reversible Basement Fan 8504164 Rev A